| Plate | Description — Plates 217-252 | Plate Added |
|---|
| Plate 217 | Preparing for construction of a power distribution center, Part 3: home location, east face | NOV 2003 |
| Plate 218 | Preparing for construction of a power distribution center, Part 4: a "long view" | NOV 2003 |
| Plate 219 | Preparing for construction of a power distribution center, Part 5: spraying with glossy black enamel | NOV 2003 |
| Plate 220 | Preparing for construction of a power distribution center, Part 6: a concealment scheme using a 00-scale power station | NOV 2003 |
| Plate 221 | Preparing for construction of a power distribution center, Part 7: terminal blocks positioned upon a black-painted board | NOV 2003 |
| Plate 222 | Preparing for construction of a power distribution center, Part 8: black board and terminal blocks in the home position | NOV 2003 |
| Plate 223 | Wiring the point motors through the distribution center, Part 1: materials and tools | NOV 2003 |
| Plate 224 | Wiring the point motors through the distribution center, Part 2: three levers and six wires | NOV 2003 |
| Plate 225 | Wiring the point motors through the distribution center, Part 3: three levers and seven wires | NOV 2003 |
| Plate 226 | Wiring the point motors through the distribution center, Part 4: circuit-labeling conventions | NOV 2003 |
| Plate 227 | Wiring the point motors through the distribution center, Part 5: labeled distribution board in home position | NOV 2003 |
| Plate 228 | Wiring the point motors through the distribution center, Part 6: lever-bank wires attached and trimmed | NOV 2003 |
| Plate 229 | Wiring the point motors through the distribution center, Part 7: close-up of lever-bank plugs and sockets | NOV 2003 |
| Plate 230 | Wiring the point motors through the distribution center, Part 8: an operating diagram in the guidebook | NOV 2003 |
| Plate 231 | Wiring the point motors through the distribution center, Part 9: a circuit table in the guidebook | NOV 2003 |
| Plate 232 | Wiring the point motors through the distribution center, Part 10: a jumper wire for the "common" bus | NOV 2003 |
| Plate 233 | Wiring the point motors through the distribution center, Part 11: shaping a jumper wire | NOV 2003 |
| Plate 234 | Wiring the point motors through the distribution center, Part 12: connecting one end of a jumper | NOV 2003 |
| Plate 235 | Wiring the point motors through the distribution center, Part 13: connecting the second jumper | NOV 2003 |
| Plate 236 | Wiring the point motors through the distribution center, Part 14: we connect the common wire to the end of the bus | NOV 2003 |
| Plate 237 | Wiring the point motors through the distribution center, Part 15: the seven remaining jumpers are ready for installation | NOV 2003 |
| Plate 238 | Wiring the point motors through the distribution center, Part 16: preparing for an electrical continuity test | NOV 2003 |
| Plate 239 | Wiring the point motors through the distribution center, Part 17: all the jumpers have been installed, and we have continuity | NOV 2003 |
| Plate 240 | Wiring the point motors through the distribution center, Part 18: an operating diagram for the embankment-level locomotive yard | NOV 2003 |
| Plate 241 | Wiring the point motors through the distribution center, Part 19: the table of circuits has been updated | NOV 2003 |
| Plate 242 | Wiring the point motors through the distribution center, Part 20: stripping wires for a common solenoid circuit | NOV 2003 |
| Plate 243 | Wiring the point motors through the distribution center, Part 21: mechanically joining the common wire to the hookup wire | NOV 2003 |
| Plate 244 | Wiring the point motors through the distribution center, Part 22: applying solder to a mechanical joint | NOV 2003 |
| Plate 245 | Wiring the point motors through the distribution center, Part 23: electrically testing a solder joint | NOV 2003 |
| Plate 246 | Wiring the point motors through the distribution center, Part 24: insulating a solder joint | NOV 2003 |
| Plate 247 | Wiring the point motors through the distribution center, Part 25: the power distribution center moved to a maintenance location | NOV 2003 |
| Plate 248 | Wiring the point motors through the distribution center, Part 26: wiring documentation displayed next to the distribution board | NOV 2003 |
| Plate 249 | Wiring the point motors through the distribution center, Part 27: common-circuit end-to-end continuity test | NOV 2003 |
| Plate 250 | Wiring the point motors through the distribution center, Part 28: the red and green solenoid wires have been soldered to red and green hook-up wires | NOV 2003 |
| Plate 251 | Wiring the point motors through the distribution center, Part 29: why it is necessary to channel the wires in the distribution board | NOV 2003 |
| Plate 252 | Wiring the point motors through the distribution center, Part 30: how to channel the wires in the distribution board | NOV 2003 |